Centrifugal Pumps in New Milford, IL

MSDB SERIES - MAGNETIC DRIVE, SEALLESS, New Milford CENTRIFUGAL PUMPS

• High specific gravity handling – over 1.8
• Engineered for corrosive fluids with polypropylene/Ryton© or PVDF/Ryton© construction
• Two stage versions contain two impellers, three stage versions contain three impellers
• Maximum working pressure up to 135 PSI (9.3 bar)
• Heads up to 300 feet (91.5m)
• High power neodymium magnetic drive system handles high specific gravity fluids
• Compact close-coupled design
• Sealless design improves reliability with no seal maintenance to perform or seal leaks
• Horizontal or vertical (with IEC motor only) installation
• Minimum flow rate is 1 gpm (.23m3/h)

New Milford, IL Small Centrifugal Pumps and How They Work

Centrifugal pumps use a rotating impeller to move fluid through a system. This impeller, which is a disk with vanes or blades attached to it, is driven by a motor and the rotation exerts a centrifugal force that causes the fluid to move away from the center of the disk. Due to the difference in pressure caused by this movement, the fluid is drawn into the pump and moved through the system. In addition to transferring fluids, these pumps can be utilized to transport gases.

New Milford Air-Operated Diaphragm Chemical Pump Designs & Their Advantages

Fluid-handling devices that employ air pressure to transfer fluids include air operated diaphragm chemical pumps. They are available in several designs, including single- and double-diaphragm models, ball valve layouts, and nonmetallic wetted component setups. These pumps are adaptable and reasonably priced. They can tolerate caustic or abrasive fluids, have high flow rates, and can prime themselves.

They can be used even if the liquid levels change because they are self-priming and can run dry without causing damage. Additionally, they require relatively little maintenance and can deliver a constant flow rate. Last but not least, because these pumps are air-operated, they are simple to install and use a small amount of electricity.

Practical Applications for Drum Pumps in New Milford, IL

• Gasoline production: The oil and gas industry uses drum pumps to transport fluids like oil.
• Agriculture: Drum pumps are used to deliver water and other fluids to plants and crops.
• Water treatment: In water treatment facilities and other locations where clean water is required, drum pumps are used to move water and other fluids.
• Manufacturing: Fluids like coolants, lubricants, and cleaning agents are transferred using drum pumps in manufacturing settings.
• Construction: To transport construction materials like concrete and grout, drum pumps can be used.
• Chemical processing: Drum pumps are used to move chemicals in a range of chemical processing applications, such as the manufacture of personal care products, food processing, and pharmaceuticals.
• Drum pumps are used in the mining sector to move fluids like chemicals and water.
• Drum pumps are used in power generation facilities, such as nuclear power plants and coal-fired power plants, to move fluids.

New Milford, IL Drum Pump Accessories

• AODDampener - AODDampener is unique pulsation dampener manufactured from 316L stainless steel with PTFE backed diaphragm, has fully automatic air control and handles a wide variety of applications.
• Liquid Level Control - The FTI Liquid Level Control is a pneumatic/mechanical device that will automatically turn the pump on and off as the liquid level changes
• Cycle Counter - The FTI Air Cycle Counter is an electronic device that counts pump cycles by detecting the presence of the valve carrier. The cycle counter can be universally used on any new or existing FTI Air pump with the proper air valve components.
• SPILLSTOP - Fully pneumatic system safely captures leaked product due to diaphragm failure and automatically shuts down failed pumps to eliminate costly product loss and prevent hazardous spills.
• Filter/Regulator - Compact, integrated design saves space and reduces piping, includes dual scale psi/Bar gage. Filters incoming air to five microns. Regulator adjusts air pressure from 7.3 to 120 psi (.5 to 8.3 bar).
• Pulsation Dampeners - Removes virtually all hydraulic shock while producing a near steady flow of fluid. Protect piping, valves and fittings from destructive pulsations and surges. Available in a wide range of materials of construction